Frintelis

Lane should-cost · Netherlands → Germany

What does a Rotterdam–Munich full truckload cost?

A 840 km lane via Venlo, then the A3 corridor past Frankfurt and Nuremberg, rebuilt from the road up: fuel, driver time, tolls, the truck and the carrier's margin. The result is what the work costs to perform, which is the number to hold a quote against.

Published 13 November 2026 · Lane: Rotterdam (NL) → Munich (DE) · Equipment: standard curtainsider semi-trailer · Fuel basis: week of 28 September 2026

€2,028Should-cost / trip
€2.414Per loaded km
€61.44Per pallet (33)
78%Fuel, labour, tolls

The short answer

The modelled should-cost of a Rotterdam to Munich full truckload is €2,028 per trip, or €2.414 per loaded kilometre, on a Dutch driver base and diesel at €2.48 per litre. Fuel is the largest element at €681, followed by driver labour at €653 and tolls at €251. A quote for this lane can be read against that figure line by line.

What assumptions is the lane costed on?

Model inputs. Every figure on this page follows from this table. Distance and country split are planner figures for the route described; drive time comes from the engine's distance model.
InputValue used in the model
Origin → destinationRotterdam (NL) → Munich (DE), via Venlo, then the A3 corridor past Frankfurt and Nuremberg
Lane distance840 km loaded — NL 175 km, DE 665 km
Empty running100 km → 940 effective km
EquipmentStandard curtainsider semi-trailer · 90 m³ · 33 pallets · 24 t payload · 3 years old
Labour baseDutch driver · 2.0 driver days · per diem applied separately
Fuel€2.48 / litre (week of 28 September 2026, origin and destination average) · 29.2 l/100 km · 275 litres per trip
Loading / unloading2 hours + 2 hours, no chargeable waiting
Driving time13 h 18 including statutory breaks (EU 561/2006)
TollsPer-country distance tariffs, 40 t five-axle Euro VI, net of VAT (NL · DE)

Where does the money go?

Bar chart of the nine cost elements of a Rotterdam–Munich truckload, led by fuel at €681, driver labour at €653 and tolls at €251.
Cost breakdown as returned by the Frintelis should-cost engine. € / km is per loaded kilometre.
Cost element€ / km€ / tripShare
Fuel0.81168133.6%
Driver labour — Dutch driver0.77765332.2%
Tolls0.29825112.4%
Profit margin0.115974.8%
Maintenance & tyres0.108914.5%
Depreciation0.101844.2%
Overhead (SG&A)0.088743.7%
Per diem0.060502.5%
Insurance & taxes0.056472.3%
Total should-cost2.4142,028100%

Reading the stack

How much are the tolls between Rotterdam and Munich?

Toll per country for a 40-tonne, five-axle Euro VI combination, net of VAT.
CountrykmToll€ / km
Netherlands175€190.109
Germany665€2310.348
Total840€2510.298

What could move the number?

Each row is a full re-run of the model with one input changed.
ChangeEffect / tripvs baseCommercial question
Diesel +10%+€74+3.7%Which index, baseline and adjustment frequency apply?
Polish driver base instead of Dutch−€366-18.1%Which establishment country does the offer assume?
Empty running +100 km+€144+7.1%Can the carrier evidence its backhaul on this lane?
Three chargeable waiting hours+€183+9.0%When does detention start, and at what hourly rate?
Margin +2 points+€39+1.9%Is margin taken on cost or on revenue?

The lane is costed on a Dutch driver base, the origin country. Run on a Polish driver base the same trip models at €1,662, which is €366 lower. That is the largest single lever in the table, so the establishment country behind an offer should be stated, not assumed.

Three chargeable hours of waiting cost €183, about €61 an hour. If a quote carries a dwell contingency, it belongs in a detention clause with a free period and an hourly rate, where it is paid only when the delay happens.

What does the lane cost per pallet?

The same trip in the units that travel into a category P&L, at full utilisation.
UnitAt should-cost
Cost per trip€2,028
Cost per loaded km€2.414
Cost per pallet (33 pallets)€61.44
Cost per m³ (90 m³)€22.53
Cost per kg (24 t payload)€0.084

How to read a quote against it

Fuel, labour and tolls are €1,585 of the €2,028: road cost that any compliant carrier on this lane has to absorb. The commercial conversation concerns the remaining €443 of asset, overhead and margin.

Four questions to take into the carrier meeting

  1. Which labour-cost base and establishment country does the offer assume?
  2. How much empty running is priced in, and what network evidence supports it?
  3. Which items are fixed, which indexed, and which treated as verifiable pass-through?
  4. What loading and waiting time is included in the linehaul, and when does detention begin?
Interpretation note

A should-cost result is a decision anchor, not a price ceiling. Market imbalance, capacity, service conditions and carrier network economics can all justify a rate above the model. The purpose is to know how much of a quote the carrier is being asked to explain.

Method and scope

Figures are produced by the Frintelis should-cost engine from the lane inputs in the assumptions table and a dated European reference set covering fuel, labour, toll, asset, maintenance and overhead cost. The model is deterministic: identical inputs return an identical result. Fuel prices are pump prices from the EU Weekly Oil Bulletin for the week of 28 September 2026; tolls are net of VAT.

This is a cost model, not a market price index. It does not observe transacted rates and it does not forecast them. In the application the same lane can be re-run with your own distance, equipment, waiting time and labour base.

Other lanes

Need this for your own lanes?

1 — Frintelis, the platform

Model your own lanes, run sensitivity testing and export the breakdown for your tender file. Currently in an invitation-only pilot.

Request pilot access

2 — Advisory: tender and cost-model support

Should-cost positions for your lane set before quotes come in, and a structured read of the field once they do. Independent: not a 4PL, not a broker, no carrier commissions.

Email Gyorgy Connect on LinkedIn